You're welcome. Disco Mode is labelled in the comments section of the controller manager, so just delete every other line and you'll have just the Disco Mode mapping. The only other software I've heard of is from xtrememapping.com but it's Mac only. Yeah this is a community where people exchange ideas and mappings free. If you've made a new mapping and you feel like sharing it, this is a good place to do it.

I see what you mean and it shouldn't take too much to fix it. I'm away travelling for the next couple of weeks so I won't be able to fix it for a while. It might be a little fiddly but if you can find the commands in the controller manager that work on the left deck, you might be able to duplicate them and map them to the right deck.

thanks for the quick response ... I never before make a midi mapping or changes but I'll try it. :)

I've just uploaded a new version, so this should be working now. I've also added the same feature to the Smart Buttons in banks 3 & 4 as well because I like the way it modulates the fx. Tried it on Bank 2 but didn't like it so much. Overall it's a cool update for the Smart Buttons, so thanks a lot for pointing it out.

1: This shouldn't happen with my mapping. The position of the knob on the controller should be the same as the position of the knob on the screen. The filters are set to Soft Takeover so if you're switching decks, you'll need to catch the knob up to the screen position first. If it's not working correctly, make sure that you've deleted or disabled other mappings in the controller Manager. 2-4: These are probably questions for the mapping forum where members can help each other with general Traktor questions. 5: It's possible, but in my mapping Shift + Jogwheel zooms the waveform, so you'd have to find a different combo.

I just watched it a minute ago.

Go to Preferences>Controller Manager>Assignment Table>Scratch and try adjusting the sensitivity of the Rotary Encoder. There are several Scratch lines in the Assignment table. You should probably set them all to the same sensitivity.

great, found, works! Seems you know everything :) thanks a lot !

I've never used the MC6000 but sure I'll try to answer a question about it. It's better to keep questions in the forum 'though so others can contribute or learn from it. There probably aren't too many people reading this post so it might be better to post in the mapping forum because there are lots of knowledgeable/helpful people there: http://forum.djtechtools.com/forumdisplay.php?f=15

Thanks! I only have MC3000 but I wish I had MC6000 too.

When you run Traktor, all of the modifiers are set to zero. You can see this if you go to Preferences>Controller Manager. When you hit the Track Select Knob, the modifiers will change to this sequence:1=0 / 2=0 / 3=6 / 4=6 / 5=1 / 6=1 / 7=1 / 8=1 and this sequence will change depending on what you're doing. Features like Smart FX, Smart Buttons, Cue Modes etc will only work if the correct modifiers are selected, so I would recommend pressing TSK. If your controller works fully without pressing TSK, then you might have another mapping loaded at the same time. That's a good point about the FX - I haven't mapped FX controls to Decks C&D, so you didn't miss anything. When I use this mapping, I find that I have SAMP. on permanently on Decks C&D, and control FX from Deck A&B. But for completeness, I think it would be good to have the FX mapped to Decks C&D so that you have the option. Maybe I'll get round to it on the next update... Cheers for the feedback.

Hey, thanks for that! I checked it and the modifiers are set to zero and after pushing the TSK they change to the sequence you wrote, so it´s all good....Would be cool if you could also mapp the FX to the Decks C&D. But for me allready a very good mapping if not the best i´ve tried out so far...It´s kinda hard to find good, working mappings for the mc 3000. Or maybe i just don´t know where to search.... Cheers!

Hi - you need to map the fx in the Controller Manager. I've added some more information in the description (above) about how to do that. I recommend watching the armyofme tutorial a few times, and then experiment with your own mapping.

Thanks, I'll try

I've just added a Builder to the download. It's basically the same mapping, but the Macro FX banks and Smart Buttons banks are empty. Using the Builder might make it easier to add your own custom fx.

I don't know. Save all your existing settings/mappings somewhere and then give it a try. If it doesn't work, just reload your previous mapping.

You're welcome!

No soy dueño de un MC6000. ¡Lo siento!

ty helps a lot. But after using this..volume fader . and other LED's do not light up. Can anything be done ?

Everything's working fine for me, so it's difficult to know what the problem might be. Do you have any other mappings active in Traktor? That might be causing a conflict. In the controller manager section, set the ports to "none" for everything except this mapping and the keyboard - or just delete them. If that doesn't work, can you describe the issue in more detail? For example, does the problem happen from start up, or only after pressing something else? Which other LEDs don't light up?

I just tried downloading and importing it, and it worked okay for me. Did you press the big track select knob to get started? This puts the deck into play mode. It won't work until you do that. Other things to check are the import settings. I recommend Preferences>Import, instead of Preferences>Controller Manager>Add>Import. But make sure that you save your existing settings before you import.