DJ2GO2 Touch for Traktor Pro 3
Description and Instructions
- based on the default Serato settings (see below for any differences).
- BROWSE (Press) - Toggle between Playlists and Tracks
- BROWSE (Turn) - Scroll Up/Down Playlists or Tracks
-
LOAD 1 - in Playlists (toggle Expand/Collapse), in Tracks (Load Deck A)
-
LOAD 2 - in Playlists (toggle Expand/Collapse), in Tracks (Load Deck B)
-
PLAY/PAUSE - Toggle
-
CUE - Press to Cue. Hold to Play.
- SYNC - Toggle On/Off
- TOUCH - Grab/Hold/Stop Track
- TURN - Move Left/Right (Sensitivity = 50%)
- MASTER LEVEL - Volume for Main Out
- LEVEL 1 - Line Volume for Deck A (in Serato controls Gain)
- LEVEL 2 - Line Volume for Deck B (in Serato controls Gain)
- CUE LEVEL - Volume for Headphone Out
-
Notes: Level 1 & 2 are set to Line Volume for use with Cruise Control
- Toggle On/Off
-
UP = Slower.DOWN = Faster
- Cycles through CUES, AUTO Loops, MANUAL Loops and SAMPLER
- PAD 1 - Hot Cue #1
- PAD 2 - Hot Cue #2
- PAD 3 - Hot Cue #3
- PAD 4 - Hot Cue #4
-
TO DELETE - [Pad Mode] + [Pad #]
- PAD 1 - 1 Beat Loop
- PAD 2 - 2 Beat Loop
- PAD 3 - 4 Beat Loop
- PAD 4 - 8 Beat Loop
- TO DELETE - Toggle On/Off
- PAD 1 - IN (Toggle to De-activate Loop)
- PAD 2 - OUT (Toggle to De-activate Loop)
- PAD 3 - Decrease Loop Size (in Serato Activate Loop)
- PAD 4 - Increase Loop Size (in Serato Re-Trigger Loop)
- PAD 1 - Play Sample in Slot 1 Cell 1
- PAD 2 - Play Sample in Slot 2 Cell 1
- PAD 3 - Play Sample in Slot 3 Cell 1
- PAD 4 - Play Sample in Slot 4 Cell 1
Chris Baynham-Hughes 5 months ago
paupau 3 months ago
I have the same problem but couldn't figure it out any suggestions?
Ralph over 1 year ago
Nevski over 1 year ago
Samples in Traktor are managed in the Remix Deck view. To switch to the Remix Deck view - click on the letter A or B (letters are colored either orange or grey). You'll see 4 columns/slots. The MIDI mapping triggers the 1st sample/cell in each column/slot.
Barry Delfin over 1 year ago
Thanks for the mapping. How can we get the samples to trigger from the remix deck say C and D instead of A and B?
JLuuuu almost 2 years ago
Nevski over 1 year ago
Possible but, which controls to map? What functions to give up to get EQ Low Pass?
JLuuuu over 1 year ago
I did the midi map adjustment myself - I replaced the line volume with the low pass kill for each deck and set line volume auto gain in Traktor. The little controller with Traktor is really powerful when you're on the go. Is really enough to play simple sets. Thanks again, for the initial midi mapping on Traktor - made my day on vacation - THX buddy
Andy almost 2 years ago
Nevski over 1 year ago
Traktor Pro 3 sometimes reverts back to the default TSI file. If this happens, go into settings and point it back at the TSI file you want to use. It usually only happens to me when I first install a TSI file, once it's set a 2nd time it sticks.
Chris Baynham-Hughes 5 months ago
I've sorted this now. Had to fiddle with the output routing plus the in-port adn out-port