VCI-100 Traktor 2.6.0 Mapping (based on DJTT VCI-100SE 3.6.4 Mapping)

Description and Instructions

VCI-100 Traktor 2.6.0 Mapping (based on DJTT VCI-100SE 3.6.4 Mapping https://maps.djtechtools.com/mappings/11)

 

I. Overview:

This mapping is intended for Vestax VCI-100 without any firmware upgrades.

This mapping is intended for use with Traktor 2.6.0.

Most of the changes made focus on remapping FX Effect controls.

All other controls beside FX Effects remain the same.

 

II. Changes:

(Description of changes refers to the OVERLAY provided by DJTT VCI-100SE 3.6.4 Mapping)

 

II.1 When CONTROL FX 1 mode is on:

Button A: FX Unit 1 Effect Parameter 1 Toggle

Button B: FX Unit 1 Effect Parameter 2 Toggle

Button C: FX Unit 1 Effect Parameter 3 Hold

Button D: Left Headphone Cue Toggle (This is the engineering flaw with the original VCI-100)

 

Knob A: FX Unit 1 Effect Parameter 1 Knob Direct

Knob B: FX Unit 1 Effect Parameter 2 Knob Direct

Knob C: FX Unit 1 Effect Parameter 3 Knob Direct

Knob D: FX Unit 1 Dry/Wet Knob Direct

 

II.2 When CONTROL FX 2 mode is on:

Button A: FX Unit 2 Effect Parameter 1 Toggle

Button B: FX Unit 2 Effect Parameter 2 Toggle

Button C: FX Unit 2 Effect Parameter 3 Hold

Button D: Sampler Toggle (This is the engineering flaw with the original VCI-100)

 

Knob A: FX Unit 2 Effect Parameter 1 Knob Direct

Knob B: FX Unit 2 Effect Parameter 2 Knob Direct

Knob C: FX Unit 2 Effect Parameter 3 Knob Direct

Knob D: FX Unit 2 Dry/Wet Knob Direct

 

II.3 When FADER FX mode is on:

Left Tempo/Pitch Fader: FX Unit 1 Effect Parameter 1 Knob Direct (same as Knob A for FX Unit 1)

Right Tempo/Pitch Fader: FX Unit 2 Effect Parameter 1 Knob Direct (same as Knob A for FX Unit 2)

 

Left Volume Fader: FX Unit 1 Effect Parameter 2 Knob Direct (same as Knob B for FX Unit 1)

Left Volume Fader: FX Unit 1 Effect Parameter 2 Button Hold (same as Button B for FX Unit 1) (Turns off when Fader reaches bottom position)

Right Volume Fader: FX Unit 2 Effect Parameter 2 Knob Direct (same as Knob B for FX Unit 2)

Right Volume Fader: FX Unit 2 Effect Parameter 2 Button Hold (same as Button B for FX Unit 2) (Turns off when Fader reaches bottom position)

 

Cross Fader: FX Unit 1 Effect Parameter 3 Knob Relative (same as Knob C for FX Unit 1)

Cross Fader: FX Unit 2 Effect Parameter 3 Knob Relative (same as Knob C for FX Unit 2)


Left Jog Wheel Tap: FX Unit 1 Effect Parameter 1 Hold (same as Button A for FX Unit 1)

Right Jog Wheel Tap: FX Unit 2 Effect Parameter 1 Hold (same as Button A for FX Unit 2)

 

Left Jog Wheel Movement: FX Unit 1 Dry/Wet Knob Relative (same as Knob D for FX Unit 1)

Right Jog Wheel Movement: FX Unit 2 Dry/Wet Knob Relative (same as Knob D for FX Unit 2)

 

II.4 Replacing KEY LOCK with DELAY FX Effect:

SHIFT + LEFT SYNC: DELAY FX chain (previously mapped to SHIFT + BUTTON D)

SHIFT + RIGHT SYNC: DELAY FX chain (previously mapped to SHIFT + BUTTON D)

 

III. Minor Changes:

Left Sync button type changed from Hold to Toggle

Tempo/Pitch Faders Rotary Sensitivity changed from 40% to 80%

In Controller Manager, assignment table has been cleaned out to accommodate only one Vestax VCI-100 Controller.

 

IV. For More Information:

All mapping changes can be found under comment column with prefix “000:”

Original Mapping: Based on DJTT VCI-100SE 3.6.4 Mapping (https://maps.djtechtools.com/mappings/11)

Problem downloading or other issues? Let us know on the forum.
-
Comments for v1.1.0
There are no comments for this version yet! Why don't you be the first.